Home > Error Code > He Drive Communication Error Code F1 03

He Drive Communication Error Code F1 03


Check wire harness connections to the motor, Motor Control Unit (MCU), and Central Control Unit (CCU). F2-E1 - Touch Pad (Keypad) Cable Unplugged - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. Event Notification: Fixed problem that existed with the 6.xx firmware. Note: The manual fix of F1 He Drive Communication Errorerror is Only recommended for advanced computer users.Download the automatic repair toolinstead. http://ivideoconverter.net/error-code/he-drive-communication-error-code-f1-01.html

Verify CCU is working by performing diagnostic test or any cycle. PeterStrijbosch replied Nov 18, 2016 at 7:34 AM OC - replication workload foobar2devnull replied Nov 18, 2016 at 5:12 AM Loading... This is the accepted answer. Changed to 15 minutes OCP: Wrong information displayed when no second Drive is installed in 4U Library RMU: Move Media showed wrong Source address and cartridge VOLSER RMU: Cleaning tapes in http://en.community.dell.com/support-forums/storage/f/1216/t/19538897

Ibm Ts3100 Tape Library Error Codes

therniom replied Nov 24, 2016 at 2:24 AM http://supplementskings.com/lege... F14 - EEPROM Error - Disconnect power and unplug unit. Hi HaraldSeipp Thanks for the help, i will implement it tomorow, the ITDT will help me a lot, now the drive appear as online but the Operator Panel continue with the Unanswered question This question has not been answered yet.

top Provide feedback Please rate the information on this page to help us improve our content. Hi Edson, if your equipment is under warranty, I would call IBM support (for your country: http://www.ibm.com/planetwide/mz/ - note that I'm not working in support. Press 'Stop/Cancel' to clear display. Drive Broken F3 01 Scd 5 So navigate to System Storage->Tape Systems->Tape Autoloaders and libraries->TS3100 and TS3200 Tape Libraries (3573-L2U, L4U and select "include prerequisite and corequisite fixes" when prompted for the download options to find the

F15 - Motor Control Unit (MCU) Error - Disconnect power and unplug unit to check wire harness connections to the motor, MCU, and Central Control Unit (CCU). Make sure there is not a siphon problem and check all hoses for possible leaks. Check wire harness connections to pressure switch, drain pump, and Central Control Unit (CCU). OCP: I/O station slot for FMR T not specified in dialog RMU: Drive Identity screen needs to change terminology from Library Master Drive to Control Path Drive Now fully supporting WORM

Note: Unit will attempt to lock itself during this error six times before displaying the error code. Ibm Tape Library Error Codes E1 - Open Thermistor - Replace thermistor. D7 = main error code 50 = error sub-code Also see, Viewing logs (Support > View Logs) RMI error log On the RMI error log, an error entry is displayed as: Press 'Stop/Cancel' to clear display.

Dell Powervault Tl2000 Error Codes

If too much detergent was used, run the unit through a Rinse/Spin cycle, and then run a Normal cycle without adding detergent. This corrupted system file will lead to the missing and wrongly linked information and files needed for the proper working of the application. Ibm Ts3100 Tape Library Error Codes Library error sub-codes The following table lists the library error sub-codes. Ibm Ts3200 Error Codes please help me find a solution.

If I were in your shoes, I'll call IBM or their representative for service - don't waste time troubleshooting. http://ivideoconverter.net/error-code/hard-drive-error-code-biohd-2.html F1-E5 - Calibration Shifted - Disconnect power for at least 30 seconds and then reconnect. This code is used by the vendor to identify the error caused. Check for drain pump failure and clean it of any debris. Hp Msl4048 Error Codes

A0 Sled range of motion out of specification NOTE: Sled is the part of the robotics assembly that moves the robot towards the OCP or back towards the drive. Replace defective part. Attachments Qualified_Drive_Code_Information.txt 1 KB Log in to reply. this contact form Ensure the EKM server IP addresses, on the Configure Library Encryption page, are the full qualifying name (e.g.

Some ideas how to get back to a working drive firmware: When searching for the appropriate drive Firmware on FixCentral, make sure that you specify the library, not the tape drive Ts3100 Firmware Don't show me this message again. nenifled replied Nov 18, 2016 at 10:36 AM I'm Removing 48 tapes (Primary...

Example: Subcode 02: drive #2 F5 Drive Unload Timeout Drive has run in a timeout while unloading a tape The subcode indicates which drive is affected.

SNMP Trap "Cleaning cartridge nearly expired" for cleaning cartridges that have a load count of 48 or 49 is a correct event. EKM Audit Log: Fixed EKM audit log showing blank VOLSER on the first mount of tape. OCP: Does not report Incompatible Magazine OCP: Fields overlap on Drive Inventory screen OCP: FC Drive monitor reports status for both fiber ports. Ibm Ts3200 Firmware I've attached the current information about supported drive codes for the current library firmware B90.

Example: Subcode 02: drive #2 F4 Drive Load Timeout Drive has run in a timeout while loading a tape. If corrections are made during any step, power should be reconnected and the unit should be tested. edsonTIGuy 270006GJAS 11 Posts ACCEPTED ANSWER Re: IBM TS3200 TAPE DRIVE DOES NOT UPGRADE THE FIRMWARE ‏2013-11-28T07:24:53Z I already solved the issue, it was one of the drives that was navigate here In some cases the error may have more parameters in F1 He Drive Communication Error format .This additional hexadecimal code are the address of the memory locations where the instruction(s) was

More... The door should now be unlocked. Personal tools Namespaces Article Search Main Page Applications AOL Internet Explorer MS Outlook Outlook Express Windows Live DLL Errors Exe Errors Ocx Errors Operating Systems Windows 7 Windows Others Windows Also check the motor and wire harness.