Hitachi Error E3
in the same refrigerant cycle. 38 Abnormality of Protective Circuit in Outdoor Unit- Failure of Indoor Unit PCB. E44 EzSQ nesting count error Subroutines, if-statement, or for-next loop are nested in more than eight layers E45 EzSQ instruction error Inverter found the command which cannot be executed. Tripping of Fuse. E41 Communications error The inverter's watchdog timer for the communications network has timed out. this contact form
The following table lists the cause associated with the error. Please try the request again. Drain test switch in test position, faulty PCB 08Louvre not opening. Error Code Name Cause(s) E40 Operator connection When the connection between inverter and operator keypad failed, inverter trips and displays the error code. http://airmaster.net/hitachi-air-conditioner-error-codes/
Hitachi Ac Error Code E9
LD 302 FlashesFlashesThermistor that is faulty 1Compressor overheat (OH) 2Defrost thermistor 3Ambient thermistor 4Narrow pipe (expansion) thermistor, for circuit 1 5Wide pipe (suction) thermistor, for circuit 1 6Narrow pipe (expansion) thermistor, E81 Excessive speed If the motor speed rises to "maximum frequency (A004) x over-speed error detection level (P026)" or more, the inverter will shut off its output and display the error Please try the request again. Panasonic Error Code Diagnosis display = H00 Abnormality / Protection control = No abnormality detected Abnormality Judgement = Emergency operation = Norma...
Other code Nos. This is not an error 03Communication error. The inverter has turned OFF the IGBT module output. Hitachi Ac Error Code E1 E11E22 CPU error A malfunction in the built-in CPU has occurred, so the inverter trips and turns OFF its output to the motor.
Ref. Hitachi Excavator Fault Codes The system returned: (22) Invalid argument The remote host or network may be down. Incorrect Wiring Connection to PCB in Outdoor Unit 39SystemAbnormality of Running Current at Constant CompressorOvercurrent, Melted Fuse of Failure of Current Sensor 43PressurePressure Ratio Decrease Protection ActivatingFailure of Compressor, Inverter 44PressureLow http://errorcodeairconditioning.blogspot.com/2010/10/hitachi-error-codes.html E21 Inverter thermal trip When the inverter internal temperature is above the threshold, the thermal sensor in the inverter module detects the excessive temperature of the power devices and trips, turning
A malfunction in the built-in CPU has occurred, so the inverter trips and turns off its output to the motor. Hitachi Split Ac Red Light Blinking This condition can also generate excessive motor heat or cause low torque. Faulty wiring, indoor or outdoor PCB faulty 04Outdoor unit fault. In such cases, initialize the inverter, and then re-set the parameters. *3 Reset cannot be released with the STOP/RESET key.
Hitachi Excavator Fault Codes
E40 Operator connection failure When the connection between inverter and operator keypad failed, inverter trips and displays the error code. If an over-voltage condition exists, the inverter enters a fault state. Hitachi Ac Error Code E9 E19 Inverter thermal detection system error When the thermal sensor in the inverter module is not connected. Hitachi Air Conditioning Technical This condition can also generate excessive motor heat or cause low torque.
E21 Inverter thermal trip When the inverter internal temperature is above the threshold, the thermal sensor in the inverter module detects the excessive temperature of the power devices and trips, turning weblink View my complete profile | error code air conditioning © 2014. E02 Over-current event during deceleration E03 Over-current event during acceleration E04 Over-current event during other conditions E05 Overload protection *1 When a motor overload is detected by the electronic thermal function, The inverter trips and turns OFF the output to the motor. Hitachi Window Ac Error Codes
The inverter has turned OFF the IGBT module output. Slim P Series K air conditioner fault codesMitsubishi PWFY air conditioner fault codesPanasonic air conditioning fault codesToshiba air conditioning fault codesService & MaintenanceCauses of Air Conditioner FailureMobile Air Conditioner safetyPortable air E10 Current detection error If an error occurs in the internal current detection system, the inverter will shut off its output and display the error code. navigate here E07 Over voltage protection When the DC bus voltage exceeds a threshold, due to regenerative energy from the motor.
Product Inquiry Catalog download (Product catalog is available in PDF format) Question & Inquiry To Page Top Motor Inverter WJ200 Series Features Specifications Dimensions Operation and Programming Terminal Functions Protective Functions Hitachi Washing Machine Error Codes Excessive Refrigerant Clogging of Heat Exchanger 46PressureHigh Pressure Decrease Protection ActivatingInsufficient Refrigerant 47PressureLow Pressure Decrease Protection ActivatingInsufficient Refrigerant. The inverter trips and turns off the output to the motor.
in the same refrigerant cycle. 38SystemAbnormality of Protective Circuit in Outdoor UnitFailure of Indoor Unit PCB.
are common with FSG and FS3 series. ** : For only 24, 30FSG1/FSG5 (220V 60Hz), *** : In case of PC-2H2 Failure of Thermistor, Sensor, Connection Related posts: Hitachi Split System The inverter trips and does not go into Run Mode until the error is cleared. Required fields are marked *Comment Name * Email * Website Categories Acson Actron Airwell Akai Amana AmeriCool Aux Baxi Bryant Carrier Chigo Chunlan Climatemaster Comfortaire Comfortmaker Daikin Danby Day & Night Hitachi Ac Error Code E6 E08*2 EEPROM error When the built-in EEPROM memory has problems due to noise or excessive temperature, the inverter trips and turns OFF its output to the motor.