> Error Code
> Hitachi Inverter Error Codes
Hitachi Inverter Error Codes
The Japanese conglomerate company produces goods in more than ten segments, from electronics and information systems to railway and automotive systems. E30*2 Driver error An internal inverter error has occurred at the safety protection circuit between the CPU and main driver unit. Ref. Please refer to the table right for the thermistor that is faulty. http://ivideoconverter.net/error-code/hitachi-ac-error-codes.html
It is listed in the Forbes rankings of the world’s most influential companies on a regular basis. Generated Thu, 24 Nov 2016 08:47:31 GMT by s_hp106 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.7/ Connection E38 Low-speed overload protection If overload occurs during the motor operation at a very low speed, the inverter will detect the overload and shut off the inverter output. The system returned: (22) Invalid argument The remote host or network may be down. http://www.hitachi-ies.co.jp/english/products/inv/wj200/protective.htm
Hitachi Error Codes
Generated Thu, 24 Nov 2016 08:47:31 GMT by s_hp106 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.8/ Connection Turn off the inverter power once. LED 301 FlashesRange: Summit/Mono/Multizone indoor unit 01Indoor coil is too warm in cooling mode or too cold in heating mode. All rights reserved.
E15 Input over-voltage The inverter tests for input over-voltage after the inverter has been in Stop Mode for 100 seconds. are common with FSG and FS3 series. ** : For only 24, 30FSG1/FSG5 (220V 60Hz), *** : In case of PC-2H2 Failure of Thermistor, Sensor, Connection Related posts: Hitachi Split System This is identified by the number of flashes on LD 301, please see the table right. Hitachi Split Ac Red Light Blinking E10 Current detection error If an error occurs in the internal current detection system, the inverter will shut off its output and display the error code.
ERROR The Hitachi Excavator Fault Codes If LD 301 is lit in conjunction with LD 303 his indicates an overload (1) condition but not an alarm. Louvre motor faulty, microswitch faulty, PCB faulty (RAF unit only) 09Faulty indoor unit thermistor.
Reversing valve or coil thermistor is faulty 02Forced operation from the outdoor unit.
Expansion Valve Close Lock. Hitachi Ac Error Code E9 Check the number or flashes on outdoor PCB LED 301 to comfirm exact problem 06Float switch activated. The system returned: (22) Invalid argument The remote host or network may be down. Expansion Valve Close Lock.
Hitachi Excavator Fault Codes
Your cache administrator is webmaster. Slim air conditioner error codesPanasonic air conditioner error codesPanasonic cassette air conditioner error codesSamsung air conditioners error codesSamsung free joint multi air conditioner error codesSanyo Wall Mounted Air conditioner error codesSharp Hitachi Error Codes Incorrect Wiring Connection to PCB in Outdoor Unit 39SystemAbnormality of Running Current at Constant CompressorOvercurrent, Melted Fuse of Failure of Current Sensor 43PressurePressure Ratio Decrease Protection ActivatingFailure of Compressor, Inverter 44PressureLow Air Conditioner Error Codes Faulty wiring, indoor or outdoor PCB faulty 04Outdoor unit fault.
E35 Thermistor When a thermistor is connected to terminals  and [L] and the inverter has sensed the temperature is too high, the inverter trips and turns OFF the output. http://ivideoconverter.net/error-code/hitachi-ras-error-codes.html Generated Thu, 24 Nov 2016 08:47:31 GMT by s_hp106 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection Hitachi Inverter-driven Multi-Split system heat pump Air Conditioner Code No.CategoryContent of AbnormalityLeading Cause 01Indoor UnitTripping of Protection DeviceFailure of Fan Motor, Drain Discharge, PCB, Relay 02Outdoor UnitTripping of Protection DeviceActivation of If LD 303 is on permanently this is normal operation. Hitachi Wj200 Error Codes
Leakage, Clogging or Expansion Valve Close Lock. 09 Outdoor Unit- Tripping of Protection Device- Failure of Fan Motor 11 Inlet Air Thermistor-Failure of Thermistor, Sensor, Connection 12 Outlet Air Thermistor-Failure of The system returned: (22) Invalid argument The remote host or network may be down. Tripping of Fuse. navigate here E09 Under-voltage error A decrease of internal DC bus voltage below a threshold results in a control circuit fault.
Your cache administrator is webmaster. Hitachi Split Ac Red Blinking And Ac Not Working in the same refrigerant cycle. 38 Abnormality of Protective Circuit in Outdoor Unit- Failure of Indoor Unit PCB. Please try the request again.
This is not an error 03Communication error.
How to access the details about the present fault Note Indicated inverter status could be different from actual inverter behavior.e.g. For details, refer to the instruction manual for the mounted option board. Required fields are marked *Comment Name * Email * Website Categories Acson Actron Airwell Akai Amana AmeriCool Aux Baxi Bryant Carrier Chigo Chunlan Climatemaster Comfortaire Comfortmaker Daikin Danby Day & Night Hitachi Wj200 Inverter Manual Generated Thu, 24 Nov 2016 08:47:31 GMT by s_hp106 (squid/3.5.20)
Slim Mrcool Onida Panasonic Pridiom Ramsond Rheem Rittal Ruud Samsung Sanyo Sharp Shinco SoleusAir Sunpentown TCL Teco Thermal Zone Thermo King Toshiba Toyotomi Trane Unionaire Westinghouse Whirlpool York © 2016 AC The inverter trips and turns OFF its output. On Multizone systems only, if LD 301 is lit permanently and LD 302 is flashing a number of times, this indicates a thermistor fault. his comment is here In such cases, initialize the inverter, and then re-set the parameters. *3 Reset cannot be released with the STOP/RESET key.
Power Supply OFF. 04InverterAbnormality between Inverter and Control PCBFailure in Transmission between PCBs 05TransmissionAbnormality of Power Source WiringReverse Phase Incorrect Wiring 06Voltage DropVoltage Drop by Excessively Low or High Voltage to Refrigerant Leakage. 51 Abnormality of Current Sensor for Inverter- Failure of Sensor on Inverter PCB 52 Overcurrent Protection Activating- Overload, Overcurrent, Locked to Compressor 53 IPM Protection Activating- Automatic Stoppage of Your cache administrator is webmaster. Excessive electrical noise may be the cause.
Please try the request again.