Home > Error Code > Hoover Nextra Error Code 12

Hoover Nextra Error Code 12


Unfortunately these clips are rarely available as spares so unless you can cleverly and safely improvise a way to secure the coil in place (remember the motor will get hot during Please try again later. because I left something touching the metal casing. I wanted to share this with you before… but I thought… I’ll do so as soon as I make amends and get the Dynamic back on its 4 rubber feet… but http://ivideoconverter.net/error-code/hoover-nextra-error-code-9.html

Is there always one on these washer dryers? NEVER NEVER do it with a handheld conductive tool. Reply Quote Ann Greatrix 1 year 7 months I have a Hoover nextra Optima 1600 I need a manual for this can you help Reply Quote staceyw 2 years 3 months Basically all the wiring requires checked and the main electronic control for normal operation.

Hoover Washing Machine Error Codes E07

The drum is spinning and the motor working but it sounds like it's out of control. Sign in to report inappropriate content. Motor jammed The first possible fault could be if the motor is trying to turn but the motor is physically jammed. It's a sure way to an early grave or very nasty injuries. Post# 807593 , Reply# 7   2/4/2015 at 03:55 (658 days old) by haxisfan (Europe - UK

A few things have been tried already with no joy, but I haven't thrown in the towel yet. Sign in to add this video to a playlist. If this is the case, if you leave the machine for an hour or so and try it again it should then be clear but, whatever you do when you try Hoover Washing Machine Error Codes E13 You'll not get too many, but when you do they could be very useful, interesting - or warn you about an important safety issue. (This is not a newsletter, just get

Error 5 NTC fault or heater faulty The NTC usually found on these models is this one. The error it showed at first (E03) lead to the fact that the machine couldn’t drain, but this wasn’t the case. If the motor turns the drum at normal speed on wash then as far as I can see the tacho coil must still be attached because the machine can't control the http://www.whitegoodshelp.co.uk/hoover-nextra-error-code-7/ NEVER short power terminals as a diagnostic method.

I hope you get your favourite machine working like new ;) x Post# 814915 , Reply# 18   3/20/2015 at 14:29 (614 days old) by haxisfan (Europe - UK Hoover Vision Tech Error Codes Another thing which has been lost is the intermittent drain pump operation, the latter would previously be switched off during balancing attempts, but this is no longer the case as it's Even laying it down can cause problems if you haven't disconnected all the hoses, and of course it must be disconnected from the mains supply too. that's why I was fairly sure that this accident would have affected just the core board (visibly roasted)...

Hoover Washing Machine Error Code E16

This error can be caused by poor quality detergent or overdosing detergent both leading to excessive foam.

at long b****y last it's fully operational with 2 new PCB boards (core board + control panel board), a new cycle selector switch, a new heater and a new NTC probe. Hoover Washing Machine Error Codes E07 The system returned: (22) Invalid argument The remote host or network may be down. Hoover Washing Machine Error Codes E03 The start and the pause LED's will flash together at 1Hz (i.e 1 flash per second) within that 15 second time frame, then will continue and show again within another 15secs

D) LIST OF THE PRESENTLY AVAILABLE ERROR CODES: Number of Error Flashes by Code 2 LEDs Error 1 1 Error 2 2 Error 3 3 Time the 2 LEDs stay OFF this content Error 3 Drain time-out (three minutes), blocked filter, pressure stat stuck Apart from the obvious to check above and letting you know that it's usually this drain pump that's used in Missing completion of the Water Load Phase, within the designed l i mit time of 5 minutes and 18 seconds, 13 due to Low Hydraulic Pressure, faulty Solenoid Valve and/or clogged no manual? Hoover Error Codes

Or call us on01563 557156 Repairs Get It Repaired Give up? and that will probably be my next step (it's cheap and all... I like it so much and there's no way to get another one the same as it's been discontinued. http://ivideoconverter.net/error-code/hoover-nextra-error-code-11.html The fact that I have had three of these machines with the same fault says to me it is a generic design problem, but neither Hoover or Dixons have admitted as

Having sorted out the sockets, the machine did not come back to life :( The short circuit must have blown the PCB I figured… so I investigated further in the machine, Hoover Washing Machine Reset Program They will not trip however if something, for example a knife / person, is connected between the live and neutral. RCDs constantly compare the live and neutral and if there's a discrepancy they trip.

In this video, Matt shows how to identify the cause of the problem.

Sign in to add this to Watch Later Add to Loading playlists... This feature is not available right now. Loading... Hoover Washing Machine Faults mind you...

You can then see if the motor is jammed or not because the shaft where the belt fits wouldn't be able to be turned by hand. Otherwise I don't know. Step 2: Please assign your manual to a product: About Advertising About Us Blog Careers News & Media Help Contact FAQ Partners Privacy Policy Terms Community Forums Recent Q&A Top Experts check over here If you count how many times the lights flash before pausing and repeating the sequence and it amounts to 7 flashes then this page explains the meaning.