Home > Error Code > Hot Tub Error Code Cool

Hot Tub Error Code Cool

Contents

If your spa is in fact overheating then it is caused by one of two things, either the temperature sensor is defective or the relays on the circuit board that operate And it seems to me it might be the problem after tracking every wire. If that does not work, the problem is in the circuit board itself. Q: What are ICD-9 codes? navigate here

ToE = Time out error. But even though I rigged the tformer by building up solder to the busted leg it is working perfectly and actually better than ever cause I spent money on a really If you’ve unplugged all three components and the breaker still trips, it’s likely the heater element. Could be the pump if there isn't a problem.

Hot Tub Error Codes

Heater is deactivated. The message will flash between "blb" and the water temperature. i put ahah in and hit pump 1 1 (it was already running on low setting it popped off. Randy Simmons I have a 0ld Jacuzzi Z150 Spa.

Contact dealer or a service technician if problem continues.OHOne of the sensors detected that the water in the hot tub is 112°F (44°C). PSoL Pressure switch open with low pump. PSoC = Pressure switch open with circulating pump. How To Fix Flo Error Hot Tub Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.

FLOW SWITCH (Heater is deactivated. Balboa Hot Tub Error Codes Rare system error. We make no representation as to the accuracy or completeness of this data and are not responsible for errors or omissions. https://spacare.com/spasideerrorcodes.aspx Flow switches are plumbed in line with the plumbing.

Do not enter the water. Marquis Spa Error Codes d) Replace the filter cartridge and verify the solution worked.4. Rare system error. Power failure.

Balboa Hot Tub Error Codes

Entire system is disabled. Better to call someone on this one. Hot Tub Error Codes Looked up how to tell if a relay is good or bad. Vita Spa Error Codes Pictured here is a Balboa® control system used in Belize Spas brand.

Heater disabled but the spa is operational.PSoC = Pressure switch open with circulating pump.PSoL = Pressure switch open with low pump.PSoH = Pressure switch open with high pump.ToE = Time out http://ivideoconverter.net/error-code/how-to-fix-190-error-code.html The noise is definitely not coming from that or any of the other two pumps or the blower. RISK OF HYPERTHERMIA (OVER-HEATING) CAUSING SEVERE INJURY, BURNS, OR WELTS. a) Remove filter cartridge in order to purge the air lock from the circulation pump intake. Hot Tub Error Code Oh

You can find the Jacuzzi J-575 replacement hot tub cover here.The Jacuzzi  J- 470 hot tub spa is a 8 person hot tub. If you still have problems, check over your temp sensor and hi limit circuits for wire or plug or sensor problems. Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit sensor malfunction Sn3 = his comment is here The hot tub will stay in this mode until the water temperature reaching 15 degrees below the set temperature.

c) Get an assistant to help turn the water on for 30 seconds. Balboa Spa Control Manual Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature.--- = "Watchdog". Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit sensor malfunction Sn3 =

If alternating with temp, may be temporary condition.

When the water is not flowing it should be OPEN, not CLOSED, if it is closed replace it. Indicates a shorted sensor and the heater is disabled.Contact Jacuzzi hot tubs dealer or a service technician.FL1 or FL2 (Flashing)When FL1 code starts flashing it means the flow switch is malfunctioning Wondering what your spa is trying to tell you? Gecko Spa Pack Error Codes Indicates a shorted sensor and spa is shut down or an open sensor and heater is disabled.Contact a Jacuzzi hot tubs dealer or a service technician.Sn2Stands for “Sensor 2” and displays

The Spa or Hot Tub Panel Displays: :IC , iCE This indicates that the auxiliary sensor detects a possible freeze condition. Q: What is the function of a computer monitor? FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end. http://ivideoconverter.net/error-code/hl-error-code-on-hot-tub.html Then turn it then turn it off.

System will restart when temp. Std Spa operating in Standard Mode. Then re-start the hot tub, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. Tweet Share53 Pin110 Share34Shares 197 This was written by my good friend Kaisa Williams from The Spa Depot, an online hot tub supply retailer.

SnS Sensors out of balance. Stands for “Overheat”- and the tub shuts down because water temp is too hot. This indicates a persistent flow problem The heater is shut down while all other spa functions continue to run normally. Spa unusable.

OHS = Overheat. Condition can cause injury or damage to spa and its components. Heater disabled but the spa is operational. You can often determine the make of the control system by looking inside the spa's equipment area.

The J-325 is one of the smaller backyard hot tubs available.The Jacuzzi Spa J-495 hot tub spa is an 8-10 person hot tub. Pressure switch is not working. Solution: If the temperature of the water is actually 108° or hotter, the temp sensor should be replaced. DO NOT ENTER THE WATER!

OHS = Overheat. On the board when power is on and one solid led light and one flashing led light that says "flash ok" next to it.