Home > Error Code > Hot Tub Error Code Ep

Hot Tub Error Code Ep


It automatically activates the pump (and the heater if necessary) to circulate the water and warm the plumbing. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. You should avoid contact with the suction drain covers when the GFCI is powered “on”. Alan porterfield Sep 05, 2016 10:25: Receive the new Spa pack know diagram no wiring diagram on inside panel of spa pack do not know where wires go for heater Carol http://ivideoconverter.net/error-code/hot-tub-error-code-hl.html

You can also check the pressure switch or flow switch with a an Ohm meter. Page 6 (1.5m) of the spa to comply with local requirements. ft. Page 10 Exposure to direct sunlight, excessive rain and snow and falling debris can cause distress to the spa’s shell material.

Balboa Hot Tub Error Codes

Page 41 Warranty Information under any circumstances be covered by the MANUFACTURER. SN, Sn1, Sn2 Sn3, HL, E1, E3, Prh, HtS, Blinking Lights Hi Limit Sensor Failure. Please contact technical support at 877- 722-4097 for service or repair. WARNING, if you go too far the pressure switch may activate with the pump off.

You can check the switch by performing the test below. To reduce risk of injury, do not allow children to use this product unless they are closely supervised at all times. Check to be sure the filter and filter basket are free of debris. Marquis Spa Error Codes If your spa is in fact overheating then it is caused by one of two things, either the temperature sensor is defective or the relays on the circuit board that operate

See M7 Sensors here. Spa Error Codes Check water level in spa. Also try it this way, Unplug the wires from the pressure switch/flow switch, turn on the pump and then jump the wires. https://www.spaparts.com.au/page/information/spa-error-codes-or-messages/ When making repairs to your spa, you should always manually turn the GFCI “off ” to eliminate risk of shock.

These error codes are similar to the ones previous, however we will be looking at these at another angle. Great Lakes Hot Tub Error Codes The final problem could be the pressure switch/flow switch itself. Page 36 Use swimming pool chemicals, muratic acid or household bleach, or chlorine tablets (trichlor) in your spa. Make sure spa is filled to proper level and that pumps are primed and filter cartridges are clean.

Spa Error Codes

Displays on the fifth occurrence of the HL or HFL message within 24 hours. https://www.poolandspacentre.co.uk/help/hot-tub-and-spa-error-codes.html The other pumps and the blower will purge for 30 seconds to 2 minutes at the end of the freeze condition. Balboa Hot Tub Error Codes Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.Next, put your How To Fix Flo Error Hot Tub It automatically activates all of the pumps and the blower to circulate water and warm the plumbing.Note: This auxiliary freeze protection functions at all times, even when another fault condition has

Today, Cal Spas™ is a renowned Global Manufacturer of Home Resort Products. http://ivideoconverter.net/error-code/hl-error-code-hot-tub.html ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: Connection to failed. Sn1 = Open sensor (heater is deactivated) or Shorted sensor (spa is deactivated). Log in / Register | (£) GBP (£) GBP ($) USD (€) EUR (Fr) CHF (kr) SEK (kr) NOK View Your Shopping Cart Your Cart Is Empty Call and speak to Vita Spa Error Codes

After pump has been running for 2 minutes temperature will be displayed.breadcrumb breadcrumb 2. If you are going to be in the spa for more than 10 minutes, you should reduce the temperature of the spa to 100ºF (40ºC) or lower. Please try the request again. weblink The Escape™ Plus Spas have 60 to 64 jets.

HL, HFL A difference in readings between temperature sensors has been detected indicating a possible water flow problem. Great Lakes Hot Tub Troubleshooting FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end. In Economy or Sleep mode, the pump may be off for hours outside a filter cycle.

Send Share This Copyright © 2016.

Flow problems are the number one source of trouble for the spa or hot tub owner. Check for excessive filter duration. It can be extremely corrosive. Hydropool Hot Tub Error Codes Press any button to reset.

The pumps and the blower will automatically activate regardless of spa status. Just like its name, the Patio™ series are patio™ size spas. Page 30 The spa is overheating. check over here The main reason is water flow through the spa control system, if water is not flowing at a rate to satisfy the pressure switch, it will result in one of the

It is the responsibility of the spa owner to insure that the spa is accessible for repairs. When the auxiliary sensor reads around 40F- (actual temperature dependent on specific auxiliary sensor used), the system provides freeze protection. A replacement temp sensor for this code is worthwhile as even if it does not solve the problem you will have removed the most common fault from your diagnosis and have Page 3 110V Spa Installation....................15 220V Spa Installation....................16 GFCI Wiring Diagram..................16 220V Spa Pack Wiring Diagram................17 Getting Started Spa Components List..................18 -21 Instructions for Filling the Spa..............22 - 23 Topside Controls

Make sure the location is free of obstacles that may interfere with delivery. Could also be low water level.