Hot Tub Error Codes
Disclaimer: Although we hope this information will be useful, error codes are subject to change without notice. Pump may also be deactivated). The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open. Heater is shut down, but other spa functions run normally.dr = Inadequate water detected in heater.dry = Inadequate water detected in heater. (Displays on third occurrence of "dr" message). http://ivideoconverter.net/error-code/hot-tub-error-codes-dr.html
If the error returns, contact your Sundance Spa dealer or a qualified service technician. Spa has shut down. PSoC = Pressure switch open with circulating pump. Check for proper spa water level and ensure pump is primed. https://spacare.com/spasideerrorcodes.aspx
Balboa Hot Tub Error Codes
HLoH Hi Limit Over Heat. In addition to the Sn, Sn1, Sn2 type of error codes, other codes for Smart Sensor spas, such as SA, Sb, SnA, SnB error codes are used on many spas and I WAS SO IMPRESSED WITH HOW QUICK YOU ANSWERED MY QUESTIONS (ON A WEEKEND ESPECIALLY, WOW!!)" - Cheryl, Lake Stevens, WA "I don't know if u guys monitor this email address
Like the name says, it was quite easy to install." James Hirsch Buffalo, NY Balboa is a trademark of Balboa Instruments - Manufacturer of Control Systems for Spas Get Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature.--- = "Watchdog". PSoL Pressure switch open with low pump. Coleman Spa Error Codes The low speed pump or circ pump will operate continuously until the temperature rises above 45° F.
The low speed pump or circ pump will operate continuously until the temperature rises above 45° F. Vita Spa Error Codes Low speed pump and heater will activate until spa reaches 65ºF.OH = High temperature condition, has reached 110ºF. If display shows only this message (blinking) spa is shut down. https://spacare.com/spasideerrorcodes.aspx One sensor has detected 118º F.
See picture below for reference FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end. Hot Tub Error Code Oh drops. button then pressing the mode or light button depending on the system. To Schedule Service Click Here: Contact Us Home | Service area | Contact Us | Testimonials | Blog Sensor plugged into jack A is not working.
Vita Spa Error Codes
pump will operate continuously until the temperature rises above 45° F.OH = Over heat. http://www.hottubworks.com/blog/spa-hot-tub-error-codes-fl-flo-flow-lf/ Do not enter the spa. Balboa Hot Tub Error Codes Quick View HOT TUB SUPPLY SUPERSTORE 1-800-770-0292 Sunday - Saturday7am - 7pm CST Customer Care | About Us | Contact Us | Track Your Order | Shopping Cart | Login Marquis Spa Error Codes Contact qualified service technician.
The Spa or Hot Tub Panel Displays: SL This indicates the system is in sleep mode and can be changed by pressing the up temp. this content Not all spa codes are errors, to inform you of trouble, but many codes are used to provide information about system mode, status or equipment operation. Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature. --- = "Watchdog". Hold Panel sensors have been pressed too many times in a short period of time. How To Fix Flo Error Hot Tub
Heater is deactivated.Sn2 = Nonfunctional temperature sensor. These error codes can be caused for several different reasons. th3/39 On startup indicates water temperature less than 39° F. http://ivideoconverter.net/error-code/hot-tub-error-codes-fl1.html Hold = Panel sensors have been pressed too many times in a short period of time.HOT = Circuit Board temperature has exceeded acceptable limit.ICE = Freeze protection.
HOT Circuit Board temperature has exceeded acceptable limit. Gecko Spa Pack Error Codes Could indicate a flow problem.LF = Persistent low flow problems. (Displays on the 5th occurrence of "HFL" message with 24 hours). Do not use spa when temperature is flashing or the OH message is displayed.
A problem has been detected which could cause damage to the hot tub or its components.
This is a normal spa function; no further action is necessary.When the auxiliary sensor reads around 40F- (actual temperature dependent on specific auxiliary sensor used), the system provides freeze protection. Spa is shut down. Contact ACC. Coast Spa Error Codes FL1 Water flow problem, inhibited or pressure switch malfunction.
Do not use spa when temperature is flashing or the OH message is displayed.HLoH = Hi Limit Over Heat. If water temperature drops 20ºF below set temperature, low speed pump and heater activates to bring temperature within 15º of set temperature.ICE = Freeze condition. 55ºF detected. FL Spa water is more than 20° F cooler than the temperature set point. check over here Protect from FreezingCover Cleaning and AdviceAcrylic Surface Care and MaintenancePurchase a "Made for Michigan" Spa Cover>Spa Cover MeasuringPurchase a Spa Cover Lift AssistantWhirlpool & Air Bath TubsSystem Cleaning-Home remedyAcrylic Surface Care
OHH = Overheat. COOL Spa water is more than 20° F cooler than the temperature set point. Contact ACC. HFL = Substantial difference between temperature sensors detected.
OH Overheating, water over 112° F. dry = Inadequate water detected in heater. (Displays on third occurrence of "dr" message). FREE SHIPPING $100+ $0.00 SIGN IN Sign In Registered Customers SIGN IN Forgot Password? All Rights Reserved.
Shut the spa power off, remove the filter and make sure all the jets are open. SL = Sleep mode Brett Aqualine Control Systems for Spas or Hot Tubs: OH = Temp exceeds 118° F Fr = Freeze condition - temp below 40° FFL = Pressure switch Is it an Error Code, or a System Status Code? ToE = Time out error.
Brett Aqualine OH = Temp exceeds 118° F Fr = Freeze condition - temp below 40° F FL = Pressure switch failure EO = Shorted temp sensor E1 = Open temp OH = Over heat. Sensor plugged into jack B is not working. YOUR KNOWLEDGE OF PRODUCTS AND THE ONLINE SERVICE HELP IS OFF THE CHART.
Spacare.com 888-772-9887 Technical Assistance 405-622-4950 0 Item(s) | Total: $0 Home Shop SpaCare.com Spa Part Index Circuit Board Repair Spa Covers Spa & Hot Tub Covers Spa Cover Lifts Rare system error. Heater is deactivated. COL Cool condition.
It automatically activates all of the pumps and the blower to circulate water and warm the plumbing. Pressure switch is not working. Sensor plugged into jack B is not working.SnS = Sensors out of balance.