Harley Davidson Engine Fault Codes
If the code is current it will reappear. 9 – Press and release the odometer reset button to continue to the next module. 10 – Turn Ignition switch to OFF. PartsSportster PartsDyna PartsSoftail PartsTouring PartsVrod PartsClassic Harley PartsEvo Era PartsMulti-Fit Parts and AccessoriesTrikes, Hacks and Trailer PartsStock Harley Take OffsGear and Other Items For SaleTrades & Freebies (See Subforums for specific Push the odometer reset button once and you will see the selection menu "PSSPt" with the first P flashing. Follow this link...The Harley School of Hard Knocks @ HDBitchin» Print Pages:  Go Up HDBitchin, a Harley Davidson Forum → Forum → The Harley School of Hard Knocks @ HDBitchin Source
Harley Davidson Diagnostic Code Reader
Run your bike and shut it down then recheck the DTCs again by repeating steps 1 to 9. The word “diag” should then appear. B2023 Rear Speaker Shortened to Battery Ignition ON After Ignition OFF for at Least 10 sec.
If the code is current it will reappear. 9 – Press and release the odometer reset button to continue to the next module. 10 – Turn Ignition switch to OFF. -------------------------- Facebook Twitter Google+ YouTube Stay In The Know Sign Up For Our Newsletter Email* This iframe contains the logic required to handle AJAX powered Gravity Forms. The Rex Review 190,011 views 1:56 Harley Davidson Softail I bought my Husband a Harley - Duration: 4:01. Harley Bcm Codes The module that is flashing is the one you are going to check.
Why Choose Fuel Moto Search By Model Choose your Ride ATV/UTV Harley Metric Offroad Smart Model Search Loading ... How To Clear Codes On Harley Davidson We're the ExpertsAsk us anything. Watch QueueQueueWatch QueueQueue Remove allDisconnect The next video is startingstop Loading... Definitions AFR – Air Fuel Ratio ATS – Air Temperature Sensor BAS – Bank Angle Sensor CCM – Cruise Control Module CKP – Crank Position Sensor.
MAP sensors replace the former VOES used on early models. Harley Davidson Model Codes Release the odometer reset button. If more than one trouble code is sent: a. For a list of places to get H-D (and other) parts at a discount, click here.
How To Clear Codes On Harley Davidson
MH MechsHands View Public Profile Find all posts by MechsHands P Related Topics Thread Thread Starter Forum Replies Last Post How To: Diagnostic Trouble Codes (DTC's) DR. http://www.hdforums.com/forum/sportster-models/302797-updated-how-to-diagnostic-trouble-codes-dtc-s.html The MAP sensor monitors the intake manifold pressure (vacuum) and sends the information to the ECM. Harley Davidson Diagnostic Code Reader Ryan Urlacher 81,575 views 15:23 HOW TO OPEN HARLEY DAVIDSON SPEEDOMETER DIAL FACE CHANGE - Duration: 20:38. Codes For Harley Davidson Models The dwell time for the ignition coil is also calculated in the microprocessor and is dependent upon battery voltage.
After the 50 trip retention period, the trouble code is automatically erased from memory (that is, assuming no subsequent faults of the same type are detected in that period). this contact form EFI – Electronic Fuel Injection EFP – Electronic Fuel Pump ET – Engine Temperature sensor FI – Fuel Injectors FPR – Fuel Pressure regulator IAC – Idle Air Control actuator IAT Password Register Forgot Password? Also if the code set is a historic code (not a constant light) after 50 start and run cycles of at least 30 seconds each in duration, the light will extinguish Harley Davidson Check Engine Light
b. Install diagnostic test wire across Terminals 1 and 2 on the data link connector. Trouble codes are read via the odometer. http://ivideoconverter.net/harley-davidson/harley-davidson-fault-finding.html Read the following to understand how to interpret the sequences: First the light will flash an 'intermission' sequence.
Turn Ignition switch to OFF. Harley Code P1511 Close Fuel Moto Products See all Fuel Moto Products Fuel Moto RaceWire RaceWire spark plug wire offers a fully sleeved 8.5mm diameter wire with a spiral wound connector and Kevlar core P0444 Purge Solenoid Open/Low 68.
EFI – Electronic Fuel Injection EFP – Electronic Fuel Pump ET – Engine Temperature sensor FI – Fuel Injectors FPR – Fuel Pressure regulator IAC – Idle Air Control actuator IAT
Term Choose One2-YearAnnualMonthlyClear Become A Member Learn More Learn at your own pace Access to our extensive library Videos at all skill levels Knowledge when you need it Select your membership B1135 Accelerometer Failed 7. Push the odometer resetbutton again to view additional codes if they exist. 7 - Record the codes. 8 - If DTC's are not to be cleared, Press and release the odometer Harley Davidson Diagnostic Codes 61121 Loading...
P0118 ET Sensor High 49. P1003 System relay contacts open 8. Turn OFF the ignition switch. Check This Out Press and release the odometer reset button to continue to the next module.
The module that is flashing is the one you are going to check. Term Choose OneAnnualClear Become A Member Learn More Description The Twin Cam allows us to see the Harley error codes also known as the diagnostic trouble codes. This feature is not available right now. Turn OFF the ignition switch.
Sign in to add this video to a playlist. Following transmission of the second digit of the first code, there is a 3 second pause in which the lamp is off. On models not equipped with a tachometer "No Rsp" will appear when the tachometer identifier is selected. "No Rsp" will also appear if the run/off switch is in the off position The CKP generates an “AC signal” which is sent to the ECM where it is used to reference engine position (TDC) and speed.
NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until 'clear' comes ECT - Engine Coolant Temperature. U1301 Serial Data High 3. Expand/collapse navigation MTC HomeMotorcycle ServiceHarley-Davidson RepairHarley Fault CodesDirt/Quad/ATV RepairTires / PartsSHOP ONLINEParts CatalogsBikes for SalePre-owned MotorcyclesAbout UsCustomer ReviewsFacebook PageContact UsDirections to our ShopNews / Specials MTC HomeMotorcycle ServiceTires / PartsBikes for
Record the codes. DTC – Diagnostic Trouble Codes ECM – Electronic Control Module. (The Computer) Computes the spark advance for proper ignition timing and fuel control based on sensor inputs (from CKP, MAP & Items sold for off-road use only are not legal in many states and provinces and are not intended for use on a public road. P2122 TGS1 Low/Open 25.
Each exhaust component is hand-built and designed from countless hours of R&D on our in house dyno. P0222 TPS2 Low 34.