Home > Harley Davidson > Harley Davidson Error Code U1301

Harley Davidson Error Code U1301

Contents

For best results, use a needle nose pliers for removal/installation on coil. This condition is normal and does not by itself indicate a malfunction. U1300 ECM Serial Data Low 4. NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until 'clear' comes Source

Harley Davidson DTC FAULT CONDITION MODULE CODES B0563 Battery Voltage High TSM/TSSM B1004 Fuel Level Sending Unit Low Instruments B1005 Fuel Level Sending Unit High/Open Instruments B1006 Accessory Line Overvoltage Instruments Press and hold odometer reset switch then turn ignition switch ON. Hopefully they are right. This does not include situations where the engine will not crank, such as a bad starter, dead battery, etc.

Harley Davidson Code List

P0108 Map Sensor High 18. EFI – Electronic Fuel Injection EFP – Electronic Fuel Pump ET – Engine Temperature sensor FI – Fuel Injectors FPR – Fuel Pressure regulator IAC – Idle Air Control actuator IAT B1154 Clutch Switch Input Short to Ground 12.

Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. This process will help you determine where to look and test. Jackpot Exhaust The leader in quality and performance. When the ignition switch is turned ON, the check engine lamp will illuminate for approximately four seconds and then turn off.

NOTE - Harley Davidson DTCs relating to the ignition coil can only be fully diagnosed during actuation. U1016 Harley Code Question about 2005 FLSTN- FLSTNI Softail Deluxe 1 Answer Fault codes ...1. NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until ‘clear' comes site:1130cc.com: HOW TO pull codes Quote: Originally Posted by rjrivero Nobody cares about your shit like you Fuel gauge?

Question about 2005 FXSTBI Softail Night Train 1 Answer Harley Code U1301 Harley Code U1301 Hi Ruggerron67, electronic control module serial data high, is what that code means. SitemapPrivacy Sign In or Create an Account Email Password Forgot Password » x FAQ's Check out popular questions Email Us We aim to reply within 24 hours Fuel Moto 920-423-3309 Mon-Fri P1514 Air Flow Fault 43. P0152 Rear Oxygen Sensor High 76.

U1016 Harley Code

The time now is 02:42 AM.

-- V-twin new ---- V-Twin Alternate Style Contact Us - V-Twin Forum : Harley-Davidson Forums - Archive - Privacy Statement - Top https://www.fixmyhog.com/video/troubleshoot-with-harley-error-codes-008010/ Turn Ignition switch to OFF & Run/Stop switch is to Run. Harley Davidson Code List P1352 Front Ignition Coil Driver High/Shorted 54. There may also be starting or performance problems.

All Harley Davidson System Problems - Fall into at least one of three general categories: Harley Davidson No Start - The engine cranks over freely, but will not start. http://ivideoconverter.net/harley-davidson/harley-davidson-error-code-p0505.html Count the number of times the lamp flashes to retrieve the second digit. The time now is 02:42 AM. -- 1130cc Main ---- 1130cc Classic ---- 1130cc - Gray ---- 1130cc Classic - Grey Contact Us - 1130cc.com: The #1 Harley I was taking it out yesterday and after a mile or two the engine icon would come on and off intermittantly.

Step 2: Please assign your manual to a product: About Advertising About Us Blog Careers News & Media Help Contact FAQ Partners Privacy Policy Terms Community Forums Recent Q&A Top Experts In this manner, there may sometimes be a false indication of the current DTC. EFI - Electronic Fuel Injection EFP - Electronic Fuel Pump ET - Engine Temperature sensor FI - Fuel Injectors FPR - Fuel Pressure regulator IAC - Idle Air Control actuator IAT http://ivideoconverter.net/harley-davidson/harley-davidson-error-code-list.html B1134 Starter Output High 14.

If no problems are found after completion of the initial diagnostic check, a comparison of running parameters may be used to help locate intermittents and out-of-specification sensors. b. The dwell time for the ignition coil is also calculated in the microprocessor and is dependent upon battery voltage.

B1152 Bank Angle Sensor (BAS) Short to Battery 10.

Using an ohmmeter, touch probes to terminals on each end of plug wire. If the code is current it will reappear. P0154 Rear Oxygen Sensor Inactive 78. P0374 CKP Sensor Synch Error 19.

Home position established by taking readings off the 22 teeth on the alternator rotor. Here's what I've done after browsing the internet a bit: 1. We don't need no stinking Fuel gauge!!! Check This Out something similar to what you are describing has happened with me awhile back on my 2010 SG.

Then it may be mechanical failure - Things to check then would be compression, cam timing, and the fuel system. TP – Throttle Position Sensor TSM/TSSM (Turn Signal/ Turn Signal Security Module) VE – Volume Efficiency VSS – Vehicle Speed Sensor. With the jumper in place, the ignition control module should recognize a high voltage. Login or Sign Up Log in with Facebook Search in titles only Search in General Service and Repairs only Advanced Search Search What's New?

Even if you bought the exhaust new, make sure you have all the mounting hardware. Tips on Engine Diagnostics, how to get codes, and what they mean. Fuel Moto ECU Flash Fuel Moto offers professional ECU flashing services for a broad range of Metric and American V-Twin models. Remove spark plug cable from spark plug and ignition coil.

Push the odometer reset button again to view additional codes if they exist. NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until ‘clear' comes Push odometer reset button in & hold. P0131 Front Oxygen Sensor Low 73.

A historic trouble code resides in the memory of the ECM until the code is cleared by use of the Scanalyzer or a total of 50 trips has elapsed. Turn Ignition switch to OFF.