Home > Hot Tub > Hot Tub Error Code Dry

Hot Tub Error Code Dry

Contents

That is not the case because the SPA shuts down within minutes of turning it on. We invite you to please Register to create a new account. Now i've got mine up way higher than that, but I have an old mechanical system with no circuit board, so I'm able to "tweak" the temp up about as high Error & LCD Window Message Codes: ACC (Applied Computer Controls) CoLd = Temperature in the spa heater housing is below 40° F. navigate here

Sometimes solids, leaves, hair, etc. Either thermostat, pressure switch, temp sensor, etc. Your heater burned up from being exhausted from running with the top off. And my heater either. http://www.spadepot.com/spa-error-codes.htm

How To Fix Dr Code On Hot Tub

Remove solids, break down alkalis, and of course oils. Q: Can you print out a Jet Blue boarding pass? Also when the tub is initially powered up the blowers go on and remain on regardless of me turning them on/off via my balboa TP600 top side panel.

My Hot Tub Won’t Heat Sometimes a heating problem is as simple as replacing a heater element, however sometimes the problem can be caused by another component. Usually a SN error code is signaling that one of the sensors is failing, but since you said that it was a possible lighting strike then your circuit board could have Q: How many pages can one ink cartridge print? Hot Tub Jets Not Working Dream Maker Hot Tubs OH = Overheat 108° F, spa is deactivated.

Id just refilled This answer was rated: ★ ★ ★ ★ ★ I have a Balboa spa with drY code showing. How To Fix Flo Error Hot Tub Since your pack is 14 years old it may be time to upgrade to a new control system. Is there anything else I can look at? http://www.troublefreepool.com/threads/86283-Spa-code-of-quot-Dr-quot-and-quot-Dry-quot-How-does-one-fix-this-issue-PLEAS-HELP!! Footer links 1 Did you know?

Have tried everything to fix it. Hot Tub Control Panel Not Working Snb = Spa is shut down. If so, how do you replace the switch? The heat light is off and the thermostat is set lower than the water temperature.

How To Fix Flo Error Hot Tub

How does one fix this issue? Shut the spa off for 20 min to reset the power. How To Fix Dr Code On Hot Tub Hello all, I seem to be having trouble getting my Lx74 spa up and running properly. Hot Tub Overheating Troubleshooting This is just to test to see if that switch is causing this.

This is sounding like a circuit board problem at this point. check over here On some systems, an alarm will sound. Could it be a pressure switch problem? I did not check to see if this was the actual temp. Balboa Hot Tub Error Codes

Thanks for the purchase! Using a volt/ohm meter, the resistance across the heater terminals (with power off and heater disconnected from pack) should be somewhere between 8-20 ohms depending on the heater.  If the measurement Shipping costs to Alaska, Hawaii and Canada are determined by weight. his comment is here If the spa was working fine prior to a drain and refill, but now it isn't, chances are you have an air-lock.

After 2-4 min of the pump running the temp will be displayed. -- Temperature not current in Economy or Sleep mode. Hot Tub Jets Won't Turn On How old is the filter cartridge in your spa? Look in the heater if possible as well.

The sensor is not reading properly.

Balboa VS510SZ Controller HFL Error Code I have a brand new Balboa VS510SZ controller heat pack installed. You would want to check your circulation pump. and the was like an electrical crackling sound when I pushed the pump button coming from the board area ... Hot Tub Air Lock Symptoms Plastic or fabric covering the drain.

Thermastadt or panel control switch?Is there a reset button or fuse in the pumps? Now if you can spin it freely with your fingers and it is just getting hot, then yes, try both capacitors first. Since it is flashing between this error code and temperature it may be a temporary condition. weblink If your spa is equipped with a circulating pump, there is a screen-like fitting in your hot tub that bubbles and/or hot water comes out of.

That's about a week and a half in production and seven days in transit. Advanced Search Forum > Swimming Pool Care > Spas and Hot Tubs > Spa code of "Dr" and "Dry". I am getting an OH message on the topside. After ten min.

The unit (Suntek) is around 14 years old should I replace the circuit board or the whole Balboa unit. Heater is deactivated. Post distance is usually 1 1/4″ between post elements. regina So my hot tub is leaking and the pump/motor does seem to be getting louder as noted above.

Jacuzzi J-365 Flatlined ---- We shut off hot tub because water was too low and went to fill it next day and was empty. The voltage from the transformer fluctuates from 12.6v to 14v ... Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit sensor malfunction Sn3 = I've tried removing the filter but the error message stays on.

P50 error message on a spa usually means a flow issue and the system will not allow the heater to come on. Through her experience and expertise, she compiled a list of common problems you might run into when taking care of your hot tub, and gives solutions on how to solve them. Too Many Closed Jets or other flow obstruction in the Main Pump Line (Pump 1) 5.