Home > Hot Tub > Hot Tub Error Code E1

Hot Tub Error Code E1

Contents

No action is necessary.PnL = Communication between the panel and circuit board is faulty.---- = "Watchdog" (spa is deactivated) A problem has been detected.Sn1 = Open sensor (heater is deactivated) or Heater is deactivated. Then re-start the hot tub, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.To check for activation: or SpaDepot.com customers with accounts enjoy these benefits: Faster checkout Order status & history Easier package tracking Manage addresses Favorites list Exclusive deals CREATE ACCOUNT SHOP AS GUEST All Products navigate here

OHH = Overheat. Note: A common programming mistake is overlapping filter times that may cause the spa to filter continuously.• Check the water level.• Check the water temperature with an accurate temperature thermometer. When the water is not flowing it should be OPEN, not CLOSED, if it is closed replace it. Water flows out but the alarm E.0.2 still appear. http://www.spadepot.com/spa-error-codes.htm

Balboa Hot Tub Error Codes

LF = Persistent low flow problems. (Displays on the 5th occurrence of "HFL" message with 24 hours). The water temperature is lower than 4C (40F). 1. No action is necessary.I CE2 = Freeze protection. Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.

F2 = 4 hours daily filtration F4 = 8 hours daily filtration F6 = 12 hours daily filtration FC = continuous filtration EasyPak C = Celsius CL = Current Time of No action is necessary. Scott Felsen 404 views 0:49 FLO Error Code - Duration: 0:43. Marquis Spa Error Codes DO NOT ENTER THE WATER!

at heater.OHS = Overheat. Spa Error Codes We are a ferry ride from Vancouver. When the water is not flowing it should be OPEN, not CLOSED, if it is closed replace it. OH = Overheating, water over 112° F.

If the water is still hotter than the set temperature, press the blower button (if applicable) to cool the spa.If your spa is not overheating based on physical vessel temperature and Great Lakes Hot Tub Error Codes Balboa (used by Belize Spas and many other hot tubs) pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F. We make no representation as to the accuracy or completeness of this data and are not responsible for errors or omissions. CLOSED or SHORTED FLOW SWITCH ON SYSTEM STARTUP (system disabled) Flow switch is non-functional.

Spa Error Codes

Make sure you buy it from an authorized dealer or you will not have your warranty honored. check these guys out If pump 1 was turned on due to this reason alone, this message will appear for up to two minutes right after very cold water is detected. Balboa Hot Tub Error Codes Filter cartridges are dirty (this is a very common cause of pump failure). How To Fix Flo Error Hot Tub This could indicate poor flow or air bubbles in the heater.

Please unplug the pump and move to a warmer ambient temperature. check over here Snb = Spa is shut down. See MoreSee LessWithout an operation a boy, 10, could die within weekshttp://www.crawleynews.co.uk A dad-of-six has made a desperate plea for help t... 1 month ago Halifax Home ShowHalifax Home Show with If condition persists, contact your Sundance Spas dealer or qualified service technician. Vita Spa Error Codes

Inspect these first:• Check slice or ball valves. The temp sensor and the high limit are usually located on the heater housing, with 1-2 small wires coming off and connecting to your controller. This alarm appears when the manual reset thermal cut-out trips off. 1. his comment is here The power port experienced some temporary current variation. 1.

Leave a Reply Click here to cancel reply. How To Fix Sn Code On Hot Tub Spa has shut down. Spa Guy 1,259 views 2:54 Balboa Legacy Systems Series - Troubleshooting Panel Message OH - Duration: 4:54.

The Spa or Hot Tub Panel Displays: SL This indicates the system is in sleep mode and can be changed by pressing the up temp.

Possible causes are an airlock in the system, lack of flow through the heater (could be caused by dirty filters, closed gate vales, or a faulty circ pump), a faulty sensor This is a normal spa function; no further action is necessary.When the auxiliary sensor reads around 40F- (actual temperature dependent on specific auxiliary sensor used), the system provides freeze protection. SE = Spa operating in Standard-in-Economy Mode. Great Lakes Hot Tub Troubleshooting If you are unsure of something or have any questions, please do not hesitate to contact us via Email.

ICE = Freeze protection. Spa unusable. FINAL NOTE: The Hi Limit Sensor is located behind a shield on the stainless heater manifold and is the smaller of the two silver bullets.Other issues that can cause these error weblink This message will disappear when the circuit board temperature drops below acceptable limit.

The most common valve; the tee handle valve, will show that the handle is up, but in many cases the gate is still half closed, make sure that it is open Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. Heater disabled but the spa is operational.