Home > Hot Tub > Hot Tub Error Code List Sns

Hot Tub Error Code List Sns

Contents

This Mode allows the User to Replace or Clean a Pressure Side Filter Cartridge without Equipment turning ON unexpectedly. If they're not, or you're not sure that both are (because you can't tell whether you have two separate flows at different rates or just one flow), momentarily turn both pumps If there is Now an Error Message, select Message Other than CFEor CONFIG ERROR below or contact your Dealer or Service Organization.No Error Messages:The "CFE" or "CONFIG ERROR" Configuration Error Appears See picture below for reference FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end. navigate here

Some Spa Brands or Models may have this Message Enabled, and the Interval between these Messages will be whatever the Spa Manufacturer has selected. The equipment stays on until the sensors detect that the spa temperature has risen to within 20 degrees of the set temperature. drops.HL = High limit switch tripped. Back to Top PHL or PH IS LOW RAISE PH Message At the pH Sensor, the "pH Level is Low" (PHL).With a pH Sensor Installed in the System, the pH Level http://www.hottubworks.com/blog/spa-error-codes-sn-sns-sn1-sn2/

Balboa Hot Tub Codes Sl

Press "Mode" Button to Clear Message. Heater is deactivated. If it's not flowing after two minutes, turn the power off and let the spa rest for a few hours, then repeat. FLO, FL, FLC, FL1, PS, Blinking Lights Pressure Switch or Flow Switch Failure.

Contact your Dealer or Service Organization.A Sensor Failure Message may indicate Excessively High Heater Temperatures which can Scald or Burn!If the Heater is Not Cool Enough to Safely Service, allow the Some products featured may be limited quantity. drops. Balboa Sn Error Code Back to Top dr or HEATER MAY BE DRY WILL RETEST SHORTLY Message There is Possibly a "Dry" (dr) Heater.

In most cases overheat issues are related to the relays on the circuit board, or the temp sensor has failed and will need to be replaced. Heater Start Up will begin again after about 1 Min. For the error messages of HFL, LF, Dr, or DRY. The "SnS", "Sn", or "SENSOR SYNC" Fault has occurred for more than 1 hour, indicating one or both Sensors are several degrees off, and Spa Functions are Disabled.

You can follow any responses to this entry through the RSS 2.0 feed. Cal Spa Hot Tub Error Codes Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact your Dealer or Service Organization.Check for All of the following Conditions:1. Contact your Dealer or Service Organization. Add pH Decreaser according to Manufacturers Instructions.Note: If you do Not have a pH Sensor installed in the Spa System, you should Never get this Message.

How To Fix Sn Code On Hot Tub

Contact your Dealer or Service Organization to check the Switch Numbers or Setting Values Displayed, and Correct as Necessary to Match the Equipment in the Spa System, or Continue for a https://spacare.com/spasideerrorcodes.aspx Balboa (used by Belize Spas and many other hot tubs) pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F. Balboa Hot Tub Codes Sl Depending on where the temp sensor is mounted; usually in the wall of the spa in a sensor mount, you could have a flow issue. Balboa Hot Tub Error Codes Heat Related Pump Not Running.8.

This is Not an Error Message. check over here ACC (Applied Computer Controls)Systems for Spas or Hot Tubs: CoLd = Temperature in the spa heater housing is below 40° F. Pump may also be deactivated). Dr, Dry Persistent low flow problems. (Displays on the fifth occurrence of the HFL message within 24 hours.) Heater is shut down, but other spa functions continue to run. Sn Error Code Hot Tub

If you still have a problemyou either have bad sensor or PC board. Could indicate a flow problem. To read the Current Water Temperature, either Change to Standard Heating Mode or turn On the Heating Related Pump, and wait at least 2 Minutes. http://ivideoconverter.net/hot-tub/hot-tub-error-code-dry.html th2/current temperature = On startup indicates temperature probe problem.

If one of these sensors needs to be replaced BOTH should be replaced at the same time. Cal Spa Sn Error Code If there is Now a Message Other than a "PSt" or "PERSIST FAIL" Persistent Memory Error Message, that Message will Now have to be Diagnosed. This is the last thing you want to happen!!!

Product Guides Spa / Hot Tub Parts Spa Cartridge Filters New Spa Sales Spa Covers Spa Accessories Spa Chemicals Aromatherapy Hot Tub Benefits Home New Products All Products Specials Search Categories

If the GFCI does not trip for some reason, the gFI fault will appear and the HOt flag will be set.If the spa is subsequently powered down and then powered up Back to Top drn or DRAINING Message While in Standby Mode, "Drain" (drn) Mode has been Activated.The "Jets 1" Button has been Pressed while in the Standby Mode, and Pump 1 Back to Top Ecn or Ec Message Ecn or Ec MessageIf the Ecn or Ec Message is Alternating with the Water Temperature on the Display, the Spa is Operating in the Balboa Hot Tub Codes F8 You must have JavaScript enabled in your browser to utilize the functionality of this website.

Contact your Dealer or Service Organization.SnS or Sn is Blinking ON and OFF:There is a Verified "Sensors out of Sync" (SnS or Sn) with Each Other Condition. YOUR KNOWLEDGE OF PRODUCTS AND THE ONLINE SERVICE HELP IS OFF THE CHART. Sn3 Open or shorted sensor ( heater disabled). weblink Spas, LifeSpas Inc., Marquis Spas, Master Spas, Moonlight Spas Inc., MoonWater Spas, Mountain Springs Spas, PDC Spas, Phoenix Spas Inc., QCA Spas Inc., Reflections Spas, Rio Swim Spas Inc., Sensation Spas,

The Heater will Only operate and Heat up to Set Temperature during the Filter Cycles. If water temperature drops 20°F below set temperature, low speed pump and heater activates to bring temperature within 15° of set temperature. In summation; when you have spa trouble codes of Sn, SnA, Sn1, Sn2. Remove the Spa Cover and allow Sanitizer to Dissipate, or do a Partial Water Change.Note: If you do Not have an ORP Sensor installed in the Spa System, you should Never

Power on the spa must be cycled before the heater will function again. At the same time this test is being done, put your hand on the stainless steel heater manifold, it should NOT be hot, it should only be at the same temperature This indicates a Problem with the Firmware (Operation Program), or the System is Operating on Unreleased Firmware (Sample or Prototype System). Contact your Dealer or Service Organization.

Pumps will run automatically. All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 365 Days, but some Spa Brands or Models may be Different. Shop By Categories Accessories Air Controls Chemicals Spa Boss Cleaners Spa Boss Sanitizers SpaBoss Water Balancers Spa Crystals Fragrances Circuit Boards Control Packs Covers Clarity Spa Covers Down East Spa Covers dry Inadequate water detected in heater. (Displays on third occurrence of "dr" message).

Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature. --- = "Watchdog". Rotomolded Spas Spa Preppers - Hurricane Spa Protection Hot Tub Circulation Pump Troubleshooting How to Measure for a Hot Tub Cover Hot Tub Electrical Safety Spa & Hot Tub Plumbing Fittings No action is necessary.I CE2 = Freeze protection. Featured[more] Classic Spa Cover by Prestige$349.00 Uni-Pack 1000 Spa Control Pack$580.00 Search Advanced Search Information About Us Shipping & Returns Privacy Notice Conditions of Use Contact Us Site Map Gift Certificate

Also try it this way, Unplug the wires from the pressure switch/flow switch, turn on the pump and then jump the wires. Unplug sensor and switch sensors around. ICE2 Freeze protection. Heater is deactivated.