Home > Hot Tub > Hot Tub Error Codes Balboa

Hot Tub Error Codes Balboa

Contents

After the Problem has been Resolved, you Must Press Any Button to Reset and Restart Heater Start Up. Your cache administrator is webmaster. Leave a Reply Click here to cancel reply. All Pumps and Blower are ON for at least 4 Minutes After Temp is 45°F (7.2°C) or Above at the Sensors, or when the Aux Freeze Switch Opens. http://ivideoconverter.net/hot-tub/hot-tub-error-codes-flc.html

HL = High limit switch tripped. There is Not enough Water in the Heater to Start it. Sn3, HL, EO, E2, E3, Prh, Prr - these all refer to the heat sensors that are usually attached to your heater manifold. Press "Mode" Button to Clear Message. http://www.spadepot.com/spa-error-codes.htm

Sl Code On Hot Tub

There may be conditions that exist in which the spa control system will be unable to detect these conditions. If there is Now an Error Message, select Message Other than CrC or CHKSUM FAIL below.No Error Messages3. Closed Slice Valve.7.

Unless the water is very cold, only the circ pump will start for one minute. ICE Freeze protection. th3/39 = On startup indicates water temperature less than 39° F. Vita Spa Error Codes Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact your Dealer or Service Organization.Check for All of the following Conditions:1.

If there is Now a "rtC" or "RTC FAILURE" Real Time Clock Error Message, contact your Dealer or Service Organization. Balboa Hot Tub Turn Off Economy Mode Test and Adjust pH Level per Manufacturers Instructions. Rare system error. Then press Temp once to exit Priming Mode.

Heat Related Pump Not Running.8. Hot Tub Control Panel Instructions The Heater and Pump will Operate Any time the Thermostat Demands Heat. HFL Substantial difference between temperature sensors detected. Snb = Spa is shut down.

Balboa Hot Tub Turn Off Economy Mode

Press "Mode" Button to Clear Message. http://www.hottubworks.com/blog/spa-hot-tub-error-codes-fl-flo-flow-lf/ If there is Now an Error Message, select Message Other than rtC or RTC FAILURE below.No Error Messages3. Sl Code On Hot Tub In some instances it may be more prudent to contact a local repairman or send Spa Care Center your control box for evaluation/repair. Balboa Hot Tub Codes F8 Press any button to reset after the problem has been corrected, or or contact your Dealer or Service Organization. 1.

Too Many Closed Jets.6. check over here Back to Top rCH or NEW FILTER Message Time to "Change Filter Reminder" (rCH)Appears Every 365 Days*. The Real Time Clock keeps the Current Time of Day. PSoL = Pressure switch open with low pump. Spa Command Panel Instructions

Since it was so cold, and my spa was in sleep mode, I opened the panel and made sure there was water ( not ice) in the heating element. (I cracked Select "Message Other than PSt or PERSIST FAIL" Below. Sensor plugged into jack A is not working. his comment is here Back to Top HFL, HL, or HTR FLOW LOW Message Possibly the "Heater Flow is Low" (HFL or HL).During Heating, this message indicates a Possible Low Flow Condition.

Dirty Filter.5. How To Get Hot Tub Out Of Economy Mode ILOC Interlock failure - possible pump or ozone spike. (---) Unknown water temperature. (Displays when first powered up after refill). Back to Top rCO or CLEAN COVER Message Time to Clean "Cover Reminder" (rCO).Appears Every 180 Days*.

Forgot your password?

The temp sensor and the high limit are usually located on the heater housing, with 1-2 small wires coming off and connecting to your controller. The "SF" Safety Fault Error Message indicates that the Vacuum Switch has closed, indicating that there has been a Suction Problem or a Possible Entrapment Situation Avoided.2. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. Balboa Hot Tub Troubleshooting This is an Operational Message, Not an Error Indication.

Back to Top Snb, Sb, or SENSOR B SERVICE REQD Message "Sensor B" (Snb or Sb) is Not Operating Correctly.The Sensor Connected to the "Sens.B" Connector on the System Board may Spa Error Codes: Sn, Sn1, HL, E2, E3, Prh For these trouble codes, the high limit sensor is open or shorted. The System will stay in the Standard Mode for 1 Hour unless the "Mode/Prog" Button is Pressed on a Panel with a "Mode/Prog" Button, or the "Temp" Followed by "Light" Buttons weblink Do not use spa when temperature is flashing or the OH message is displayed.

Back to Top PHH or PH IS HIGH LOWER PH Message At the pH Sensor, the "pH Level is High" (PHH).With a pH Sensor Installed in the System, the pH Level