Home > Hot Tub > Hot Tub Error Codes E1

Hot Tub Error Codes E1

Contents

Please contact the Bestway UK Aftersales Team 3. A problem has been detected which could cause damage to the hot tub or its components. drops. Loading... navigate here

Check for clogged filter.FL2 = Pressure switch problem. Contact ACC. ISO 9001 Company Canadian Spa Company is a quality assured company meeting ISO 9001 standards. Log in / Register | (£) GBP (£) GBP ($) USD (€) EUR (Fr) CHF (kr) SEK (kr) NOK View Your Shopping Cart Your Cart Is Empty Call and speak to http://www.spadepot.com/spa-error-codes.htm

Balboa Hot Tub Error Codes

Check the water temperature with an accurate temperature thermometer. One sensor has detected 110°F. Heater disabled but the spa is operational.SESH = Sensor short, nonfunctional. Now feel totally let down and our enjoyment has turned to thoughts of " what a waste of money " ...

Why can't this company guarantee a ship date and stick to it? ... Balboa (used by Belize Spas and many other hot tubs) pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F. ILOC = Interlock failure - possible pump or ozone spike . (---) =Unknown water temperature. (Displays when first powered up after refill). Marquis Spa Error Codes Then re-start the hot tub, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.To check for activation:

Mon - Fri 9am - 5pm Calls cost 5p plus your phone company's access charge Categories Search Spa Shop Pool Shop Sauna Shop Leisure Shop Search Search You are here: Home Make sure that they are open. After starting or during the functions of filtering or/and heating, the water flow sensors do not detect water flow. 1. http://www.hottubworks.com/blog/spa-error-codes-sn-sns-sn1-sn2/ Check the water level.

Just nu 9995:-!! - Duration: 0:43. Great Lakes Hot Tub Error Codes Communication between control panel and/or remove control panel and circuit board is faulty. Loading... at heater.OHS = Overheat.

Spa Error Codes

In extremely hot weather, check for proper cabinet ventilation. See MoreSee Less 2 weeks ago Hello we are looking to buy a hot tub. Balboa Hot Tub Error Codes This must be repaired only be a Sundance Spas dealer or qualified service technician. Vita Spa Error Codes No action is necessary.

Contact your Sundance Spas dealer or qualified service technician. check over here Make sure that all jets are open, and nothing is blocking the spa drain cover flow. Please contact the Bestway UK Aftersales Team E.0.1. th3/39 = On startup indicates water temperature less than 39° F. How To Fix Flo Error Hot Tub

Sn3, HL, EO, E2, E3, Prh, Prr - these all refer to the heat sensors that are usually attached to your heater manifold. Improving our customers quality of life, delivering unique products and outstanding customer care. See MoreSee Less 1 month ago Duncan ross ‏@gardendesigncom Nottingham, EnglandOne of the first hot tubs we installed 20 years ago #Nottingham @CanadianSpaCo pic.twitter.com/t20ou7aWnm ... http://ivideoconverter.net/hot-tub/hot-tub-error-codes-flc.html No action is necessary.I CE2 = Freeze protection.

The spa is not designed to operate with water temperatures lower than 4C (40F). How To Fix Sn Code On Hot Tub See M7 Sensors here. ICE = Freeze condition. 55°F detected.

Remove the spa cover and allow the water to cool.

The hot tub will stay in this mode until the water temperature reaching 15 degrees below the set temperature. Power on the spa must be cycled before the heater will function again. The equipment stays on until the sensors detect that the spa temperature has risen to within 8.0°C of the set temperature. Great Lakes Hot Tub Troubleshooting At the same time this test is being done, put your hand on the stainless steel heater manifold, it should NOT be hot, it should only be at the same temperature

CLOSED or SHORTED FLOW SWITCH ON SYSTEM STARTUP (system disabled) Flow switch is non-functional. This could indicate poor flow or air bubbles in the heater. th2/current temperature = On startup indicates temperature probe problem. weblink You can check the switch by performing the test below.

Balboa Control Manufacturer Scroll past Common Error Codes for: What common codes actually mean and what you can check prior to scheduling service Common Spa or Hot Tub Error In most cases a replacement pressure / flow switch for this code is worthwhile as even if it does not solve the problem you will have removed the most common fault FLO* = Flow Switch (heater is deactivated. Tony Durrant 3,011 views 3:31 # 37 Why do spa heaters fail? - Duration: 9:12.

System will restart when temp. Pressure switches are in contact with the water, when you remove it water will come out (or should).NOTE: Most spas are equipped with pressure switches and can be found threaded into The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open. You can follow any responses to this entry through the RSS 2.0 feed.

Sign in 3 0 Don't like this video? Sn3 = Open or shorted sensor ( heater disabled). Balboa Control Systems for Spas or Hot Tubs: pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F.OHH = Overheat. Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit sensor malfunction Sn3 =

Brandon E 48,278 views 9:24 Loading more suggestions... When the water is not flowing it should be OPEN, not CLOSED, if it is closed replace it. You should have continuity. The pump's thermometer is broken. 2.

Make sure they aren't touching anything. This must be repaired only be a Sundance Spas dealer or qualified service technician. Please contact the Bestway UK Aftersales Team E.0.8. See picture below for reference FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end.

Once this is done check ACROSS the heater element post, you should have either 110 volts or 220 volts depending on what voltage is operating the control box. If you have followed Steps 2 and this has not been successful, please remove the filter set, activate the filter or heat system and put your hand in front of the Shut the spa down, remove the filter and make sure all the jets are open.