Home > Hot Tub > Hot Tub Error Codes Flo

Hot Tub Error Codes Flo

Contents

Then turns off, could I check any other cause of this before I replace pump? After I posted, the FLO message was on, I dropped the temp setting and I left the cover off over night. FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end. If it does you know you need a new pressure switch. navigate here

If the Flashing FLO message did not go away when you removed the filter then you possibly have an obstruction or blockage in the circulation system. COOL = Spa water is more than 20° F cooler than the temperature set point. Once I powered it up, it ran and heated the water. This will reset the system. https://spacare.com/commonspasideerrorcodes.aspx

Where Is The Flow Switch On A Hot Tub

If the problem persists you could have a bad PWA. Sign in to make your opinion count. Contact your Sundance Spas dealer or qualified service technician. "WATCHDOG" (hot tub is deactivated). If neither of these are the case you could have a bad Flow Switch or a bad connection to the Flow Switch.

If the Flashing FLO message goes away within a minute then you have found where the problem lies with a dirty or soiled filter. If you suspect that this is the case, see the instructions on page 77 under "pump does not operate and icon does." Circuit board temperature has exceeded acceptable limit. Damon August 20, 2016 Reply Thanks for the reply Nigel, I really appreciate it. Hydropool Hot Tub Flow Error Nigel August 21, 2016 Reply Damon check your temperature with a couple of external thermometers.

If it has a seperate circ pump than maybe that is bad? -Jay Pam April 20, 2016 at 1:42 pm There is just one pump and it runs both speeds without Hydropool Hot Tub Error Codes The first thing that you want to do if you get these error codes, is actually take your breaker and turn it off and then turn it back on. I have a cal spa classic select -41. 7000 control panel. 2, motors. http://precisionpool.net/2010/12/hot-tub-low-flow-error-causes-and-solutions/ I did that and it didn't seem to work either.

The spa runs perfect on both speeds and there is great jet action but the spa will not heat because of the FLO code. Hot Tub Flow Switch Troubleshooting I am not a caldera dealer so do not know their boards. Problem 2 LF low flow at certain times with no heat, and a dry warning, not sure what that means, but doesn't sound good. SEoP = Sensor open or disconnected.

Hydropool Hot Tub Error Codes

Up next Pressure Switch Flow Code No Heat Spa Hot Tub How To The Spa Guy - Duration: 8:14. Posted in:hot tubs and spasspa troubleshooting See more Prev:In-ground Pool Installation Pictures Rowley, MA Back: All Posts Next:In-ground pool building permits, setbacks, and building codes About the Author JayB Jay is Where Is The Flow Switch On A Hot Tub I noticed that the flo got weaker over a couple days. Flc Error Code On Hot Tub The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open.

Replies Theresa Nielsen January 03, 2015 Reply Our topside display flashes flo cool, what does this mean? check over here If you hook a flexible hose up to the discharge side of the Flow switch and run this directly over the lip into the spa and receive no solid FLO msgs A new UV bulb can be purchased from a local Sundance Spas dealer. F2 = 4 hours daily filtration F4 = 8 hours daily filtration F6 = 12 hours daily filtration FC = continuous filtration EasyPak C = Celsius CL = Current Time of Sundance Hot Tub Flo Error

You can leave a response, or trackback from your own site. If your Topside is displaying a Solid FLO message you will have no water movement in the spa. From here the troubleshooting takes you inside the spas service area and should be looked at by an experienced technician. Step 3. http://ivideoconverter.net/hot-tub/hot-tub-error-codes-flc.html See "Water is too hot" (page 77).

It has maintained the temp for 3 days. Vita Spa Error Codes If you are a die hard do it yourself'er and want some guidance through the troubleshooting process feel free to send us an email at: [emailprotected] Please make sure to include This must be repaired only be a Sundance Spas dealer or qualified service technician.

Laurent November 08, 2015 Reply Hi, I have the same problem and tried to remove filter, release the air lock from the bib but still showing "Flo & Cool".

I am lost. Contact your Sundance Spas dealer or qualified service technician. Virginia Wood May 9, 2015 at 10:53 pm We have a vita spa. Marquis Spa Error Codes Thanks Nigel November 08, 2015 Reply Laurent what make and model spa do you have and also what is the date built?

More How to release an air lock in your spa More The 5 Best Hot Tub Brands in America 2015 More Home Meet Precision Contact Us The Blog 978-388-2585 NavigationHome Power fluctuation in the secondary power line is causing the DC voltage to be low. ICE = Freeze protection. weblink I have everything hooked back up the way it should be with a new board.

Pressure switch is not working. Spa is shut down. So, I filled the tub and cleaned the filters.