Home > Hot Tub > Hot Tub Error Codes Oh

Hot Tub Error Codes Oh

Contents

If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1. It may just be the impeller is worn or broken and may not require a completley new pump, just some parts. CLOSED or SHORTED FLOW SWITCH ON SYSTEM STARTUP (system disabled) Flow switch is non-functional. All Rights Reserved. http://ivideoconverter.net/hot-tub/hot-tub-error-codes-flc.html

Rotomolded Spas Spa Preppers - Hurricane Spa Protection Hot Tub Circulation Pump Troubleshooting How to Measure for a Hot Tub Cover Hot Tub Electrical Safety Spa & Hot Tub Plumbing Fittings Back to Top SAH or SANITIZER HIGH Message At the ORP Sensor, the "Sanitizer Level is High" (SAH).With an ORP Sensor Installed in the System, the Sanitizer Level is Above 830 Balboa Control Systems for Spas or Hot Tubs: pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F.OHH = Overheat. If it's not flowing after two minutes, turn the power off and let the spa rest for a few hours, then repeat. http://www.hottubworks.com/blog/spa-hot-tub-error-codes-oh-ohh-omg/

Balboa Hot Tub Error Codes

All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 7 Days, but some Spa Brands or Models may be Different. If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1. OPEN or SHORTED SENSOR (heater disabled) The main temperature sensor is non-functional. Gender:Female Posted December 17, 2010 · Report post what cover did you take off?

So simple, it almost made me go nuts fixing it myself. If it's 230v you may be getting 115v through your topside control/flow switch and then the other 115v through the high limit circuit. If water is flowing from the circ pump outlet, proceed to test all the other pumps.If the Circ Pump is primed, or if you Do Not have a Circ Pump, then:- Vita Spa Error Codes This is a normal spa function; no further action is necessary.When either sensor reads below 40 degrees F., the system provides freeze protection.

Take off the Heat shield cover to allow the water to cool down. Hot Tub Overheating Troubleshooting The System will stay in the Standard Mode for 1 Hour unless the "Mode/Prog" Button is Pressed on a Panel with a "Mode/Prog" Button, or the "Temp" Followed by "Light" Buttons Balboa Control Manufacturer Scroll past Common Error Codes for: What common codes actually mean and what you can check prior to scheduling service Common Spa or Hot Tub Error check over here A solid red light indicates that immediate attention is required to clear or fix an error code.

Then continue on to the next pump.- If the display exits Priming Mode and shows dashes or a temperature or a mode indication (such as Std or Ecn or SLP) before Great Lakes Hot Tub Error Codes If there is Now an Error Message, select Message Other than CFEor CONFIG ERROR below or contact your Dealer or Service Organization.No Error Messages:The "CFE" or "CONFIG ERROR" Configuration Error Appears The idea is that, if anything in the file changes, the checksum will change and Result in a CrC Error.At Power-Up, the System has Failed the Program Checksum Test. This must be repaired only be a Sundance Spas dealer or qualified service technician.

Hot Tub Overheating Troubleshooting

Shut the power down, remove the two wires to the pressure switch/flow switch, find some sort of wire to join the wires, but don't do it yet.

If you don't want to go to your local dealer you can find the pumps several places online. Balboa Hot Tub Error Codes FINAL NOTE: Most spas are equipped with pressure switches and can be found threaded into the stainless steel heater manifold. How To Fix Flo Error Hot Tub Take out the Microfilter and clean or replace it.2.

Then press Temp once to exit Priming Mode. this content Gender:Female Posted December 13, 2010 · Report post Super clean the filters, even if the pump is moving water, it may not be moving enough. The sensor plugged into sensor “B” jack is malfunctioning.Contact your store for the hot tub unit to be serviced if the problem continues.SnS or SnMeans that the sensors are not in Powered by vBulletin Copyright © 2016 vBulletin Solutions, Inc. Marquis Spa Error Codes

No action is necessary.PnL = Communication between the panel and circuit board is faulty.---- = "Watchdog" (spa is deactivated) A problem has been detected.Sn1 = Open sensor (heater is deactivated) or Duplicate actions used for “OHH”. Safety should ALWAYS be your first consideration! weblink On the subsequent power-ups, the GFCI test is skipped because the proper flag has been set in the software.Note: The GFCI Test Feature should only be Enabled in the United States

Categories Consumer Research for Best Hot Tub (100) hottubworks.com (127) life (130) spa chemicals (67) spa covers (161) Spa Crystals (11) spa filter (31) spa heater (25) Spa Ozone (17) Spa Cal Spa Error Codes this information is being provided for informational purposes only. Shut the spa down, remove the filter and make sure all the jets are open.

Sending a digital picture is very helpful in helping us to troubleshoot or answer any questions.

The leak is coming out of a tube that has a wire going through to what I am guessing is the dual filter housing. A new UV bulb can be purchased from a local Sundance Spas dealer. The spa repair company also gave us a new ozonator. Great Lakes Hot Tub Troubleshooting This turns on pump 1, and also turns on the circ pump.- Verify that both pump 1 and the circ pump are running and that water is flowing out of both

Email Address: Bath/Spa Professionals Homeowners Home | Contact Us | About Us | My Account | Shipping Policy | Return Policy | Privacy Policy | Terms & Conditions | Cannot Find One sensor has detected 110ºF.Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit Back to Top Snb, Sb, or SENSOR B SERVICE REQD Message "Sensor B" (Snb or Sb) is Not Operating Correctly.The Sensor Connected to the "Sens.B" Connector on the System Board may check over here Should I take the drain plugs out of the wet end to see if there is anything in the pump?

Heat Related Pump Not Primed. It appears there is a sensor wire inside a hose that is probably mounted at the bottom one of the filters & it looks like the hose is glued to the No corrective action is necessary. Does anyone have any ideas?

The Spa or Hot Tub Panel Displays: dr, dry This indicates that there is not enough water in the heater.