Home > Hot Tub > Hot Tub Error Codes Sl

Hot Tub Error Codes Sl

Contents

FL = Flow. I CE2 = Freeze protection. If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1. The error codes above are related to a temperature sensor failure, overheat problems or a flow problem. navigate here

I specialize in electrical questions and I am most familiar with spas that were manufactured by NEMCO, Regency, Hydro Spa, Gulfcoast Spas, Leisure Bay, and Premium Leisure. The "SF" Safety Fault Error Message indicates that the Vacuum Switch has closed, indicating that there has been a Suction Problem or a Possible Entrapment Situation Avoided.2. If the "SF" Error Message is not cleared from the topside panel display, contact your Dealer or Service Organization. Back to Top rCH or NEW FILTER Message Time to "Change Filter Reminder" (rCH)Appears Every 365 Days*.

Balboa Hot Tub Turn Off Economy Mode

If you do not see water flowing from the circ pump outlet, IMMEDIATELY turn off power to the spa (as an attempt at heating will occur within a minute of the Standard mode maintains the desired temperature. Click here to read about who we are. Dirty Filter.5.

Heat Related Pump Not Running.8. Back to Top ICE, IC, or FREEZE COND Message A Potential Freeze Condition has been Detected, and "Ice" (ICE) in the System is being Prevented.44°F (6.7°C) or Lower has been Detected Ask Fix my Pool and Spa Your Own Question Fix my Pool and Spa, Owner / Technition Category: Pool and Spa Satisfied Customers: 1052 Experience: Over 24 years in pool and Balboa Hot Tub Codes F8 Back to Top rt9 or TEST GFCI Message Time to "Test GFCI Reminder" (rtg).Appears Every 30 Days*.

SN = Non functional high temperature sensor. Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode.2. If it still trips with pump removed, plug the pump back in and onto the next component. navigate here Below is a list of common error codes from the top manufacturers of control equipment for hot tubs.

The spa will only heat up to temperature in the Standard mode. Hot Tub Control Panel Instructions It's worth a thousand words. Back to Top Your cart is empty. Balboa (used by Belize Spas and many other hot tubs) pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F.

Balboa Hot Tub Error Codes

Heater is deactivated. Heater is shut down, but other spa functions run normally. Balboa Hot Tub Turn Off Economy Mode Our Privacy Policy has details and opt-out info. 800-787-6649 Register Log in Register Your Spa Financing 800-787-6649 Register Log in Register Your Spa Financing Close Hot Tub/Spa Selector Why Strong? How To Get Hot Tub Out Of Economy Mode Back to Top rCA or CHANGE MINERAL CARTRIDGE Message Time to "Change Mineral Cartridge Reminder" (rCA)Install a New Mineral Cartridge per Manufacturers Instructions.

All Reminder Messages can be Disabled through the Topside Panel Users Menu.Note: The Balboa Default is to have this Message Disabled. check over here Ecn = Spa operating in Economy Mode. We accomplish this in many ways. If you haven't successfully primed both pumps by the time the Priming Mode display ( Pr or PRIMING MODE depending on panel) ends, turn off the spa IMMEDIATELY.If after two minutes Ec Code On Hot Tub

Edit Close Save changes Attachments: Added items Uploading: 0% my-video-file.mp4 Complete. The System will stay in the Standard Mode for 1 Hour unless the "Mode/Prog" Button is Pressed on a Panel with a "Mode/Prog" Button, or the "Temp" Followed by "Light" Buttons Do not let the pumps run for a total of more than 2 minutes if they haven't primed by then. http://ivideoconverter.net/hot-tub/hot-tub-error-codes-flc.html Press "Mode" Button to Clear Message.

You have it in "Sleep" mode. Spa Command Panel Instructions Back to Top rtr or TREAT WOOD Message Time to "Treat Wood Reminder" (rtr).Appears Every 180 Days*. Low Water Level.2.

Apr 10, 2014 | Jacuzzi Balboa R574 System for 1 2 Speed... 0 Answers Do I have the correct controller for my hot tub?

We’ve been Providing custom quality Hot tub Covers and Spa Covers at a great price and with great service since 2005.Visit Our Official Site Enter your email address to subscribe to If a continuously running low-speed-only pump is only used for filtering (not for heating), that is not called a circ pump, but instead may be referred to as a "continuous filtration Press any button to reset after the problem has been corrected, or or contact your Dealer or Service Organization. 1. Balboa Hot Tub Troubleshooting Sn2 = Nonfunctional temperature sensor.

It is where all the wiring goes and has a metal tube along the bottom; you will need a Phillips screwdriver to remove the cover. On them you need to press the 'TEMP' button and then the 'LIGHT' button within three seconds of each other and this will change the modes from EC (economy mode), to Then continue on to the next pump.- If the display exits Priming Mode and shows dashes or a temperature or a mode indication (such as Std or Ecn or SLP) before weblink Email Address: Bath/Spa Professionals Homeowners Home | Contact Us | About Us | My Account | Shipping Policy | Return Policy | Privacy Policy | Terms & Conditions | Cannot Find