Hot Tub Error Codes Sn
System will restart when temp. Contact your Dealer or Service Organization.SnS or Sn is Blinking ON and OFF:There is a Verified "Sensors out of Sync" (SnS or Sn) with Each Other Condition. Advanced Search Forum > Swimming Pool Care > Spas and Hot Tubs > SN code on Balboa control Welcome to Trouble Free Pool We would like to welcome you to TFP, PnL = Communication between the panel and circuit board is faulty. ---- = "Watchdog" (spa is deactivated) A problem has been detected. his comment is here
One of the sensors detected that the water in the hot tub is 110°F (43.3°C).DO NOT GET INTO THE WATER. Low speed pump and heater will activate until spa reaches 65ºF.OH = High temperature condition, has reached 110ºF. If your spa is not overheating and you are getting the above error codes then a couple of things need to be investigated. Back to Top CrC or CHKSUM FAIL Message "Cyclic Redundancy Code" (CrC) Checksum Error.A "Cyclic Redundancy Code" (CrC) is a type of checksum algorithm that takes a string of data bytes http://www.hottubworks.com/blog/spa-error-codes-sn-sns-sn1-sn2/
Balboa Hot Tub Error Codes
this information is being provided for informational purposes only. These error codes are caused by a variety of reasons. Alvin Shepherd 7,103 views 7:57 Replacing the Costco Aruba hottub pump - Duration: 7:06. Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact your Dealer or Service Organization.Check for All of the following Conditions:1.
Loading... Back to Top StU or STUCK ON Message A Pump appears to be "Stuck" (StU) ON, and the Water is Too Hot.If the spa is configured with the GFCI Trip Feature All Reminder Messages can be Disabled through the Topside Panel Users Menu.Note: The Balboa Default is to have this Message Disabled. Marquis Spa Error Codes I CE2 = Freeze protection.
diy collaborative 12,054 views 17:46 Balboa Legacy Systems Series - Troubleshooting Panel Message OH - Duration: 4:54. Working... Watch Queue Queue __count__/__total__ Find out whyClose How to repair hot tub error code SN3 diy collaborative SubscribeSubscribedUnsubscribe349349 Loading... Sign in Statistics 12,230 views 15 Like this video?
If alternating with temp, may be temporary condition. Balboa Hot Tub Codes Sl Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode.2. Press "Mode" Button to Clear Message. Test and Reset the G.F.C.I.
How To Fix Sn Code On Hot Tub
Then re-start the hot tub, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.
Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact your Dealer or Service Organization.Check for All of the following Conditions:1. Balboa Hot Tub Error Codes It automatically activates the pump (and the heater if necessary) to circulate the water and warm the plumbing. Vita Spa Error Codes balboawatergroup 4,895 views 4:18 Balboa Legacy Systems Series - Troubleshooting Topside Panels and System Outputs - Duration: 6:37.
Blocked Skimmer.4. this content OH = High temperature condition, has reached 110°F. Switch closed while pump is deactivated.COL = Cool condition. code displayVerify that all the knife valves are open. How To Fix Flo Error Hot Tub
If this alternating with the temp, it may just be a temporary condition. Low Water Level.2. Inspect these first:• Check slice or ball valves. http://ivideoconverter.net/hot-tub/hot-tub-error-codes-flc.html Also LMI metering chlorine dispenser pump and HotSpring Jetsetter I use and endorse TFtestKits TF-100 from http://tftestkits.net ~Remember TFP counts on your donations to keep this site ad free~ Reply With
Heat Related Pump Not Primed. Great Lakes Hot Tub Error Codes Check for Extended Pump Operation or High Ambient Temp, or contact your Dealer or Service Organization.Spa Water Cool Down• In order for the Spa Water Overheat Error Message to Automatically Reset Contact qualified service technician.
On some systems, an alarm will sound.
GET IN THE KNOW! × Sign up for the MSP Email Updates Be the first to know about: Exclusive sales & discounts Maintenance tips & guides Manual updates, and more! Published on Nov 11, 2014Check out this helpful how-to video on troubleshooting and correcting an SN3 error code on a Leisure Bay hot tub. To read the Current Water Temperature, either Change to Standard Heating Mode or turn On the Heating Related Pump, and wait at least 2 Minutes. Great Lakes Hot Tub Troubleshooting Do not use spa when temperature is flashing or the OH message is displayed.
Product Technical Support Help Me Replace A Part Product Manuals Product Color Codes Spa Panel Messages Topside Panel Manuals Common Spa Problems System Cross Reference Home>Balboa Spa Panel Messages Balboa Common Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit sensor malfunction Sn3 = If the flow rate still seems less than normal with all jets and valves open, you may consider inspecting for broken valves (closed when they appear to be open), clogged impeller check over here Blocked Suction Fitting.3.
balboawatergroup 6,362 views 2:47 Loading more suggestions... One sensor has detected 110ºF.Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit Low Water Level.2. Heater is deactivated.Sn2 = Nonfunctional temperature sensor.
HOT, OL, HL, FLO, Sn… SPA TEMPERATURE SENSOR ERROR CODE FLOW CHART Here's a Cal Spa troubleshooting chart for when your spa topside display shows a sensor error code Sn, Sn1, The sensor plugged into sensor “A” jack is malfunctioning.Contact your store if you continue to see this problem. If you have a Circ Pump, do this first (EL version):- Push the Jets 1 button once. Jeff Bond 11,933 views 2:48 Fix your own hot tub #4 D 115 - Duration: 2:57.
Read our FAQ! Low speed pump and heater will activate until spa reaches 65°F. While in Sleep mode your hot tub will filter 2 times a day for 2 hours a piece. The "SF" Safety Fault Error Message indicates that the Vacuum Switch has closed, indicating that there has been a Suction Problem or a Possible Entrapment Situation Avoided.2.
After about 45 Seconds, Check for Error Messages on the Topside Panel Display. Under NO circumstances should a pump be allowed to run without priming beyond the end of the 4 minute Priming Mode. Heater is deactivated. Loading...
These are similar to the Sn1 and Sn2 codes, signaled from the high limit or water temperature sensors. ICE Potential freeze conditions. softcellelectrical 130,473 views 6:27 Balboa Legacy Systems Series - Pressure Switch Calibration - For non M7(TM) systems - Duration: 4:17. Locey Swim & Spa 35,775 views 4:24 DIY Hot Tub Control - Duration: 7:57.
SnA & SnB Spa is shut down.